DIY streamer with volumio in standard 43cm box

Diy and Tweaks
122

So, I need drivers for 5.10.92, right?
Will ask them.
Folks, thank you for a moment!

1 Like
123

I would not expect a driver that was built for another kernel version to work. I doubt that the display would even show the boot sequence.

124

Yes.

125

Well just to try, it’s 5 minutes vs 2 months shipping back to china


1 Like
126

Yes, not much to lose apart from time (5 minutes? Maybe if one knows what to do). :wink:

127

Maybe a idea there is a bulleye test release i don’t know if it’s up2date.

Nope it’s not up2date

1 Like
128

And in the worst case, since those china wholesalers aren’t keen on returns, Install Raspbian and a aquarium screensaver :smile:

:fish: :blowfish: :tropical_fish:

129

Contacted to Waveshare if they can make 5.10.92 drivers or even planning. Will see.
@gvolt you are right no even boot sequence. Crap

@Wheaten this one will try to sell on eBay and on the meantime get another one HDMI :slight_smile:

130

Make sure that you pay close attention to where the HDMI and USB connector resides. As you need additional space in your enclosure.

And wait for Waveshares feedback and if they don’t provide the driver, ask if they will swap the display.

image
image1060×226 57.5 KB

131

Yes
 It is tight and this is the reason why I choose current one with DSI tape instead HDMI/USB sockets on top
 Ehhh

Waveshare got holidays to 7th of October.
Folks, thanks for advice and will contact you soon.

132

yeah they have a public holiday for a week.

1 Like
133

What an amazing streamer, that front panel is gorgeous. My question is related to the touch detection, how does it work through suck a thick glass? Thanks

134

Hi it’s a beautiful streamer.
Allegedly, this is a good combination :
ALLO DIGIONE SIGNATURE + ALLO REVOLUTION USB DAC.
What do you think?
But it is very ugly. Is it possible to make a project with “your design”?
Txs

135

Hi; i bought a display 8.8” on aliexpress, i try to run it with pi4, but i didnt do it. What is my wrong?
Note: pi4 works with AOC 24” monitor without problem and Display works on pc without problem

TRY 701.94 30 Off | 8.8 INCH 1920x480 IPS STRETCHED BAR DISPLAY RASPBERRY PI AIDA64 AUTOMOTIVE LCD DISPLAY 60Hz DRIVER BOARD LONG STRIP DISPLAY

image
image1080×1920 142 KB

image
image1080×1920 174 KB

image
image1920×1080 262 KB
image
image1920×2560 352 KB

136

your width and height are the same in your userconfig.txt
in the last 2 lines. max buffer height should be 480

2 Likes
137

ı downloaded userconfig txt on 2sn post and it is already like this. Do i need to changelast line with 480?

text1
text11286×856 180 KB

text2
text2762×298 41.6 KB

138

yes your height is max 480 and not 1920
1920 is the width of your screen

and don’t see any settings in the seconde post here.

i would advice you to contact the seller for the settings.

1 Like
139

thanks i wiil change it and i will let you know.

140

it is not work.

141

i think you hdmi timings is still off
@gvolt do you know anything about this screen ?
could not find any info about this one.

you could try this :

hdmi_cvt=480 1920 60
hdmi_drive=1
hdmi_mode=87
hdmi_group=2
display_rotate=1
hdmi_force_mode=1
#dtoverlay=vc4-fkms-v3d

if you have the last line in your userconfig mark it with a # so it will not run.
and do that for the hdmi_timings to instead use the hdmi_cvt line.

1 Like