gkkpch
September 17, 2023, 8:12pm
633
Had a quick look at your log, quite a number of acpi errors, meaning parts of hardware components were not recognized/ initialised and the Xorg display manager failed to start. You only have a terminal interface at the moment. I will have a closer look tomorrow, but as said, there is not much I can do.
@wheaten : could you please move this conversation to the proper place? Thanks.
gkkpch
September 18, 2023, 1:03pm
635
The S10-3 has an Intel GMA3150 graphics interface which requires OpenGL 2.1 or higher.
With Volumio 3 this is not supported anymore and I can’t think of a workaround for you either, sorry.
mkl1900
September 18, 2023, 2:08pm
636
Thanks for checking gkkpch, I will try the beta version if it works. Appreciate your help.
gkkpch
September 18, 2023, 5:12pm
637
Understanding the issue now, I’m sure the beta won’t work either.
gkkpch
September 19, 2023, 8:04am
639
(Edited)
lsusb
from the commandline?
gkkpch
September 19, 2023, 2:32pm
642
Booting from an SD card is very rare on an x86 device, so I have not done anything to prepare that.
gkkpch
September 19, 2023, 2:33pm
643
Strange, this is what I use now and want to replace. It tested it with Volumio and it works fine.
gkkpch
September 19, 2023, 4:44pm
645
Unlike WIndows, Linux and Mac do not need specific drivers for DAC hardware as they have a generic sound driver (with some additional dac-specific quirks. e.g. for DSD compatibility).
gkkpch
September 21, 2023, 9:58pm
647
Finally closed this Orico usb to nvme adapter issue, caused by missing UAS (usb attached scsi) support in our initramfs.@JMZ for reporting this issue, would not have found it otherwise.
To be released with the next version of Volumio 3, with current and upcoming 6.1 kernel.
1 Like
gkkpch
September 22, 2023, 9:35pm
649
Little present, full blown Volumio beta version:Volumiobuster-3.542-2023-09-22-x86_amd64
Continue to use the existing image with ausb key or switch to a full-blown beta with Orico, your choise.
Not sure about when the switch takes place, not my call.
Cheers - Gé
Case now closed for me
I installed two new Volumio latest version 3.5xx on two Dell wy3040 boxes. When boot from USB, iOS app and HomeAssistant can find these, but after install to inner EMMC storage and boot from it, I can only access Volumio from Web.
Is it right?
1 Like
Wheaten
October 15, 2023, 4:57pm
651
Did you run the complete setup and validate the given ip?
Yeah, installed to inner storage and complete all setup procedures.
Play music very well, including FLAC and DSD files.
I use http://…/dev to enable SSH, but the log is:
Starting Live Log...
info: CorePlayQueue::getTrack 0
info: CoreCommandRouter::volumioGetQueue
info: CoreStateMachine::getQueue
info: CorePlayQueue::getQueue
info: CoreCommandRouter::executeOnPlugin: system , getHwuuid
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: CALLMETHOD: system_controller system enableLiveLog true
info: CoreCommandRouter::executeOnPlugin: system , enableLiveLog
info: Launching a new LiveLog session
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: Listing playlists
info: Listing playlists
info: CALLMETHOD: system_controller system enableSSH true
info: CoreCommandRouter::executeOnPlugin: system , enableSSH
volumio : TTY=unknown ; PWD=/ ; USER=root ; COMMAND=/bin/systemctl start ssh.service
pam_unix(sudo:session): session opened for user root by (uid=0)
pam_unix(sudo:session): session closed for user root
volumio : TTY=unknown ; PWD=/ ; USER=root ; COMMAND=/bin/systemctl enable ssh.service
pam_unix(sudo:session): session opened for user root by (uid=0)
Reloading.
/lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
getty@tty1.service: Current command vanished from the unit file, execution of the command list won't be resumed.
Reloading.
/lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
Reloading.
/lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
pam_unix(sudo:session): session closed for user root
info: enable SSH service success
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
**error: Could not load host key: /etc/ssh/ssh_host_rsa_key**
error: Could not load host key: /etc/ssh/ssh_host_dsa_key
error: Could not load host key: /etc/ssh/ssh_host_ecdsa_key
fatal: No supported key exchange algorithms [preauth]
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: Listing playlists
info: Listing playlists
wlan0: WPA: Group rekeying completed with 08:55:31:b1:54:5a [GTK=CCMP]
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: Listing playlists
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: CoreCommandRouter::volumioGetState
info: CorePlayQueue::getTrack 0
info: Listing playlists
info: Listing playlists```
I have the same problem with Volumio x86, rel. 3,546, installed on a Futro S900, with a USB Wifi dongle.
I wiped the inner EMMC and re-install Volumio 3.546, it seems OK.
volumiodown
description: Desktop Computer
product: Wyse 3040 Thin Client (07C1)
vendor: Dell Inc.
serial: 5FVV5P2
width: 64 bits
capabilities: smbios-3.0.0 dmi-3.0.0 smp vsyscall32
configuration: boot=normal chassis=desktop family=Wyse sku=07C1 uuid=44454C4C-4600-1056-8056-B5C04F355032
*-core
description: Motherboard
product: 0G56C0
vendor: Dell Inc.
physical id: 0
version: A00
serial: /5FVV5P2/CNWSC0091N00E9/
*-firmware
description: BIOS
vendor: Dell Inc.
physical id: 0
version: 1.2.5
date: 08/20/2018
size: 64KiB
capacity: 16MiB
capabilities: pci pnp upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb biosbootspecification netboot uefi
*-memory
description: System Memory
physical id: b
slot: System board or motherboard
size: 2GiB
capacity: 2GiB
capabilities: ecc
configuration: errordetection=multi-bit-ecc
*-bank
description: Row of chips DDR3 1600 MHz (0.6 ns)
physical id: 0
slot: Motherboard
size: 2GiB
width: 8 bits
clock: 1600MHz (0.6ns)
*-cache:0
description: L1 cache
physical id: 12
slot: CPU Internal L1
size: 224KiB
capacity: 224KiB
capabilities: internal write-back
configuration: level=1
*-cache:1
description: L2 cache
physical id: 13
slot: CPU Internal L2
size: 2MiB
capacity: 2MiB
capabilities: internal write-back unified
configuration: level=2
*-cpu
description: CPU
product: Intel(R) Atom(TM) x5-Z8350 CPU @ 1.44GHz
vendor: Intel Corp.
physical id: 14
bus info: cpu@0
version: Intel(R) Atom(TM) x5-Z8350 CPU @ 1.44GHz
slot: SOCKET 0
size: 599MHz
capacity: 1920MHz
width: 64 bits
clock: 80MHz
capabilities: lm fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb pti ibrs ibpb stibp tsc_adjust smep erms dtherm ida arat cpufreq
configuration: cores=4 enabledcores=4 threads=4
*-pci
description: Host bridge
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register
vendor: Intel Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: 36
width: 32 bits
clock: 33MHz
configuration: driver=iosf_mbi_pci
resources: irq:0
*-display
description: VGA compatible controller
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Configuration Registers
vendor: Intel Corporation
physical id: 2
bus info: pci@0000:00:02.0
version: 36
width: 64 bits
clock: 33MHz
capabilities: pm msi vga_controller bus_master cap_list rom
configuration: driver=i915 latency=0
resources: irq:131 memory:90000000-90ffffff memory:80000000-8fffffff ioport:f000(size=64) memory:c0000-dffff
*-generic:0
description: Signal processing controller
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Power Management Controller
vendor: Intel Corporation
physical id: b
bus info: pci@0000:00:0b.0
version: 36
width: 64 bits
clock: 33MHz
capabilities: msi pm cap_list
configuration: driver=proc_thermal latency=0
resources: irq:129 memory:9152c000-9152cfff
*-generic:1
description: SD Host controller
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SDIO Controller
vendor: Intel Corporation
physical id: 11
bus info: pci@0000:00:11.0
version: 36
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration: driver=sdhci-pci latency=0
resources: irq:17 memory:91529000-91529fff
*-usb
description: USB controller
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller
vendor: Intel Corporation
physical id: 14
bus info: pci@0000:00:14.0
version: 36
width: 64 bits
clock: 33MHz
capabilities: pm msi xhci bus_master cap_list
configuration: driver=xhci_hcd latency=0
resources: irq:118 memory:91500000-9150ffff
*-usbhost:0
product: xHCI Host Controller
vendor: Linux 5.10.188-volumio xhci-hcd
physical id: 0
bus info: usb@1
logical name: usb1
version: 5.10
capabilities: usb-2.00
configuration: driver=hub slots=7 speed=480Mbit/s
*-usb:0
description: Audio device
product: Combo384 Amanero
vendor: Amanero Technologies
physical id: 3
bus info: usb@1:3
version: 1.97
serial: 413-001
capabilities: usb-2.00 audio-control
configuration: driver=snd-usb-audio speed=480Mbit/s
*-usb:1
description: Generic USB device
product: 802.11ac NIC
vendor: Realtek
physical id: 4
bus info: usb@1:4
version: 2.00
serial: 123456
capabilities: usb-2.00
configuration: driver=rtl8821cu maxpower=500mA speed=480Mbit/s
*-usbhost:1
product: xHCI Host Controller
vendor: Linux 5.10.188-volumio xhci-hcd
physical id: 1
bus info: usb@2
logical name: usb2
version: 5.10
capabilities: usb-3.00
configuration: driver=hub slots=6 speed=5000Mbit/s
*-generic:2
description: Encryption controller
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine
vendor: Intel Corporation
physical id: 1a
bus info: pci@0000:00:1a.0
version: 36
width: 32 bits
clock: 33MHz
capabilities: pm msi bus_master cap_list
configuration: driver=mei_txe latency=0
resources: irq:128 memory:91300000-913fffff memory:91200000-912fffff
*-pci
description: PCI bridge
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port #1
vendor: Intel Corporation
physical id: 1c
bus info: pci@0000:00:1c.0
version: 36
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:117 ioport:e000(size=4096) memory:91400000-914fffff
*-network
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:01:00.0
logical name: eth0
version: 15
serial: 6c:2b:59:4c:51:57
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=5.10.188-volumio firmware=rtl8168h-2_0.0.2 02/26/15 latency=0 link=no multicast=yes port=twisted pair
resources: irq:16 ioport:e000(size=256) memory:91404000-91404fff memory:91400000-91403fff
*-isa
description: ISA bridge
product: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU
vendor: Intel Corporation
physical id: 1f
bus info: pci@0000:00:1f.0
version: 36
width: 32 bits
clock: 33MHz
capabilities: isa bus_master cap_list
configuration: driver=lpc_ich latency=0
resources: irq:0
*-pnp00:00
product: PnP device PNP0c02
physical id: 1
capabilities: pnp
configuration: driver=system
*-pnp00:01
product: PnP device PNP0501
physical id: 2
capabilities: pnp
configuration: driver=serial
*-pnp00:02
product: PnP device PNP0c02
physical id: 3
capabilities: pnp
configuration: driver=system
*-pnp00:03
product: PnP device PNP0c02
physical id: 4
capabilities: pnp
configuration: driver=system
*-pnp00:04
product: PnP device PNP0b00
physical id: 5
capabilities: pnp
configuration: driver=rtc_cmos
*-network
description: Wireless interface
physical id: 1
bus info: usb@1:4
logical name: wlan0
serial: 20:0d:b0:44:40:99
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rtl8821cu driverversion=5.10.188-volumio ip=192.168.20.138 multicast=yes wireless=IEEE 802.11AC
System: Host: volumiodown Kernel: 5.10.188-volumio x86_64 bits: 64 compiler: N/A Console: tty 0 dm: N/A
Distro: Debian GNU/Linux 10 (buster)
Machine: Type: Desktop System: Dell product: Wyse 3040 Thin Client v: N/A serial: <filter> Chassis: type: 3 serial: <filter>
Mobo: Dell model: 0G56C0 v: A00 serial: <filter> UEFI: Dell v: 1.2.5 date: 08/20/2018
CPU: Topology: Quad Core model: Intel Atom x5-Z8350 bits: 64 type: MCP arch: Airmont rev: 4 L2 cache: 1024 KiB
flags: lm nx pae sse sse2 sse3 sse4_1 sse4_2 ssse3 bogomips: 11520
Speed: 999 MHz min/max: 480/1920 MHz Core speeds (MHz): 1: 1441 2: 979 3: 779 4: 819
Graphics: Device-1: Intel Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Configuration Registers vendor: Dell
driver: i915 v: kernel bus ID: 00:02.0 chip ID: 8086:22b0
Display: tty server: X.org 1.20.4 driver: modesetting unloaded: fbdev,vesa tty: 174x57
Message: Unable to show advanced data. Required tool glxinfo missing.
Audio: Device-1: cht-bsw-rt5672 driver: cht-bsw-rt5672 message: bus/chip ids unavailable
Device-2: Intel HDMI/DP LPE Audio driver: HdmiLpeAudio message: bus/chip ids unavailable
Device-3: MCS type: USB driver: snd-usb-audio bus ID: 1-3:2 chip ID: 16d0:071a serial: <filter>
Sound Server: ALSA v: k5.10.188-volumio
Network: Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet vendor: Dell driver: r8169 v: kernel port: e000
bus ID: 01:00.0 chip ID: 10ec:8168
IF: eth0 state: down mac: <filter>
Device-2: Realtek type: USB driver: rtl8821cu bus ID: 1-4:3 chip ID: 0bda:c811 serial: <filter>
IF: wlan0 state: up mac: <filter>
Drives: Local Storage: total: 7.28 GiB used: 1.05 GiB (14.4%)
ID-1: /dev/mmcblk1 model: H8G4a size: 7.28 GiB serial: <filter> rev: 0x8 scheme: GPT
Partition: ID-1: / size: 3.61 GiB used: 164.4 MiB (4.5%) fs: overlay source: ERR-102
ID-2: /boot size: 168.4 MiB used: 61.2 MiB (36.4%) fs: vfat dev: /dev/mmcblk1p1
Sensors: Missing: Required tool sensors not installed. Check --recommends
Info: Processes: 166 Uptime: 14h 57m Memory: 1.86 GiB used: 718.3 MiB (37.7%) Init: systemd v: 241 runlevel: 5 default: 2
Compilers: gcc: N/A Shell: bash v: 5.0.3 running in: tty 0 (SSH) inxi: 3.0.32
Thanks for the reply, unfortunately it is an attempt that I have already made twice, with the same result, the configuration of my PC is Futro S900, 4 GB of RAM, 500 GB SSD on SATA connector, which contains the operating system and music tracks, such as said a WiFi dongle (I used both a TP-Link Archer T2U and a TP-Link Wireless N Nano) as well as the USB DAC. Could you please specify your configuration better. Thank you.
Just to add another bit of mystery, if I start the Futro with just the Wifi Dongle, and after making sure that the Wifi works, I connect the USB DAC, it is detected, and if I select its use, everything works perfectly, until it turns off. When you turn it back on, all the problems start all over again.
Wheaten
October 16, 2023, 2:16pm
657
Please post two logs :
Also provide the output in both situations of:
This is the log of the hot-plugged DAC, working properlyhttp://logs.volumio.org/volumio/xcFcyOl.html
This is the log of the DAC and WiFi entered cold, and which prevents the WiFi from working, it is understood that given the lack of WiFi connection, to be able to read the log, I also had to connect the LAN cable.http://logs.volumio.org/volumio/1k50PlF.html
I confess that for:
“sudo lshw”
I do not know how to do.
Thanks